Multilink PPPとは Multilink PPPは、複数のPPPリンクを束ねて仮想的な1つのリンクにする技術のことです。Multilink PPPにより PPPリンクの物理ポートを束ねることでより広い帯域幅を通信に利用できます。
multilink bundle-name authenticated!! interface Embedded-Service-Engine0/0. no ip address. shutdown! interface GigabitEthernet0/0. no ip address. shutdown. duplex auto. speed auto! interface GigabitEthernet0/1. no ip address. shutdown. duplex auto. speed auto! interface Serial0/0/0. no ip address. shutdown. clock rate 2000000! interface Serial0 ip name-server 200.3.250.1 ip name-server 190.104.163.57 no ipv6 cef! multilink bundle-name authenticated!! crypto pki trustpoint TP-self-signed-1725015630 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-1725015630 revocation-check none rsakeypair TP-self-signed-1725015630!! crypto pki certificate chain TP-self-signed-1725015630 multilink bundle-name authenticated! diagnostic bootup level minimal spanning-tree extend system-id ! redundancy mode none crypto isakmp policy 7 encr 3des authentication pre-share group 2. crypto isakmp key testkey address 212.12.13.2 ! crypto ipsec transform-set juniperset esp-3des esp-sha-hmac mode tunnel ! crypto map testmap 7 ipsec-isakmp multilink bundle-name authenticated! interface Loopback0. ip address 209.165.200.225 255.255.255.0! interface Embedded-Service-Engine0 / 0. no ip address. shutdown! multilink bundle-name authenticated! interface Loopback0. ip address 198.133.219.1 255.255.255. 255! interface Embedded-Service-Engine0 / 0. no ip address. shutdown! Mar 08, 2012 · Cisco IOS software builds a multilink bundle name based on the PPP authenticated name first, then based on the endpoint discriminator. With Cisco IOS in its default state, all client links that use the same username are bundled together into the same MP virtual connection.
Mar 06, 2020 · CCNA RSE Lab: 3.2.1.9 Configuring Basic RIPv2 CCNA 2 Lab 3.2.1.9 lab – configuring basic ripv2 packet tracer Answers Topology Addressing Table Objectives Part 1: Build the Network and Configure Basic Device Settings Part 2: Configure and Verify RIPv2 Routing Configure RIPv2 on the routers and verify that it is running. Configure a passive interface. […]
Jan 15, 2020 · Last configuration change at 11:27:41 UTC Fri Jun 2 2017 upgrade fpd auto version 15.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! boot-start-marker boot-end-marker ! ! no aaa new-model no ip icmp rate-limit unreachable ! ! no ip domain lookup ip cef no ipv6 cef Jun 21, 2018 · Create the crypto map on R1, name it CMAP, and use 10 as the sequence number. A message displays after the command is issued. A message displays after the command is issued. R1(config)# crypto map CMAP 10 ipsec-isakmp % NOTE: This new crypto map will remain disabled until a peer and a valid access list have been configured.
Jan 31, 2019 · multilink bundle-name authenticated!! interface Embedded-Service-Engine0/0. no ip address. shutdown! interface GigabitEthernet0/0. description LAN with 500 hosts. ip address 172.16.252.1 255.255.254.0. duplex auto. speed auto! interface GigabitEthernet0/1. description LAN with 1,000 hosts. ip address 172.16.248.1 255.255.252.0. duplex auto
no ip bootp server ip domain name internode.on.net ip name-server 192.231.203.132 ip name-server 192.231.203.3 ! multilink bundle-name authenticated ! ! username Jan 16, 2020 · ip name-server 8.8.8.8 ip cef no ipv6 cef multilink bundle-name authenticated!!! license udi pid xxxxxxxxxxxxxxxxxxxxxx!!! redundancy!!!!! interface Embedded-Service-Engine0/0 no ip address shutdown! interface GigabitEthernet0/0 description to the ISP ip address xxxx xxxx ip nat outside ip virtual-reassembly in duplex auto speed auto! multilink bundle-name authenticated ! archive log config hidekeys ! interface Loopback0 ip address 172.16.2.1 255.255.255.224 ! interface Loopback1 ip address 172.16 Jul 18, 2020 · multilink bundle-name authenticated!!!!! redundancy!!!!! interface Loopback0 ip address 1.1.1.1 255.255.255.255! interface Tunnel0 ip address 172.16.0.1 255.255.255.0 no ip redirects ip nhrp map multicast dynamic ip nhrp network-id 1 tunnel source 192.168.1.2 tunnel mode gre multipoint! interface Ethernet0/0 ip address 192.168.1.2 255.255.255.0! Aug 28, 2012 · ip domain name yourdomain.com no ipv6 cef multilink bundle-name authenticated license udi pid CISCO891-K9 sn FCZ16xxxxxxx username tssuser password 0 1xxxxxxx interface FastEthernet0 interface FastEthernet1 interface FastEthernet2 interface FastEthernet3 interface FastEthernet4 interface FastEthernet5 interface FastEthernet6 interface FastEthernet7